DELIVERY DESTINATION

CURRENCY

LANGUAGE

VAT

UPDATE

DELIVERY DESTINATION

CURRENCY

LANGUAGE

VAT

UPDATE

enquiries@agngdiesel.com

01869 247 248

Open: 9am - 5pm MON - FRI

£ GBP

Saved

Account

Garage

£0.00

Car & Light Commercial

Heavy Commercial

Testing Services

Reconditioned Injectors

Reconditioned Fuel Pumps

Used Test Equipment

Used Tools

Test Equipment & Tools

Hello

Car & Light Commercial

›

Heavy Commercial

›

Testing Services

›

Reconditioned Injectors

›

Reconditioned Fuel Pumps

›

Test Equipment & Tools

›

Home / Car & Light Commercial / Fuel Injectors / Fuel Injectors / Reconditioned Delphi Diesel Fuel Injector 28307309

RECONDITIONED

Specification

OE Number

Specification

INSTALLATION

Features

Description

Part number

28307309

Alternative numbers

28307309,A6510703087,A 651 070 30 87,HRD350

Engine codes

OM 651.958, OM 651.957, OM 651.956, OM 651.955

Quantity in pack

GTIN

5050100167382

Trade number

28307309

Replaces numbers

28307309, HRD350, A 651 070 30 87, A6510703087

OE 28307309 - Delphi

OE 6510703087 - MERCEDES-BENZ

OE A651 070 3087 - MERCEDES-BENZ

This fuel injector has been remanufactured to the highest standards and tested on the test bench.

Common rail injectors of all brands require coding of the unique calibration code (found on the injector) to the engine ECU.

Please check the part number against your part number if you are not sure it is the right item contact us.

New injector C3i code for ECU.
New copper washer.
Each injector been cleaned and provide test report.
Injector requiring programming to you ECU.
Injector built in positive pressure room.

DFl1.5 Common Rail Injector Bleeding Procedure.

Some Delphi injectors have been reported to suffer from the control valve sticking on
fitment (air lock), this is due to continuous actuation of the valve before diesel fuel has had
sufficient time to lubricate the valve and valve seat therefore there is metal to metal
contact. In the absence of a High Pressure Fuel System Bleed function on a diagnostic
tool and to improve component lubrication during bleeding the below procedure should
be followed to prevent internal parts sticking/seizing.
The recommended bleeding procedure is as below.

1. Fit injectors to vehicle, observing all cleanliness and torque settings.
2 .Fit new seating washers and high pressure lines and torque to spec.
3. Leave all injector electrical connectors disconnected and crank engine for 7-10 secs.
4 .Wait for 15 seconds to prevent overheating of components.
5. Crank engine again for a further 7-10 secs.
6. Reconnect injector electrical connectors and crank again to start the engine.
7. Clear all fault codes from engine management ECU.
8. Coding each injector to ECU and pilot relearn.

In addition to the above procedures it is imperative that all open fuel fittings be
covered/capped at all times when working on Common Rail Fuel Systems.

When more than one injector fails on a vehicle within a short time it is likely that the problemis caused by contamination or debris passing through the internal components and damagingthe operating surfaces.

Please check the part number against your part number if you are not sure it is the right item contact us.

The item will state:

New (Original box)
-New see details (Plain box)
Reconditioned
Remanufactured

New Reconditioned & Remanufactured are a properly rebuilt part which has been completely disassembled, cleaned and examined for wear and breakage. Worn out, missing or non-functioning components have been replaced with new or rebuilt components. It is the functional equivalent of a new part and is virtually indistinguishable from a new part.

Please be aware you may be charged import duties in your country!

Pumps and Injectors carry a 12-month warranty against manufacturing or remanufacturing defects, limited to the cost of the replacement part only.

Reconditioned Delphi Diesel Fuel Injector 28307309

Name: Reconditioned Delphi Diesel Fuel Injector 28307309
Brand: Delphi
SKU: 28307309-REMAN
Price: 100.00 GBP
Availability: InStock